Jump to content


Photo

GoldenEye update

  • Please log in to reply
34 replies to this topic

#1 BDS316

BDS316

    Vanguard

  • -----
  • Posts: 2071
  • Joined: 16 Sep 2009
  • Loc: Sol 3

Posted 26 November 2012 - 05:14 PM

http://www.astrogood...e.goldeneye.jpg

This is my modified and upgraded XT8 of which I have previously reported.

The list of mods and upgrades is as follows:

Base scope was $300 back in 2006, The last of the XT8's to be sold with the rack and pinion focuser, eyepiece holder and navigation knob. Also included was the basic laser collimator that I don't use.

Moonlite CR2, $300
Bob's knobs for secondary, $15
Fender washer for secondary, 34 cents
FirstBase mount, $200
Telrad, $40
digital inclinometer, $30
flocking opposite the focuser, free from a fellow CNer
Tectron collimation tools
Doughnut magnet counterweights, $15

I have not applied ebony star to the alt bearings on the advice of CNers in a previous post. Works great as is.

Last week we split epsilon llyrae at only 109x and saw abundant surface detail on Jupiter. Last summer we were able to use the digital inclinometer to find Saturn in broad daylight. Tracking near the zenith/Dobson's hole is doable at 300x-plus.

I'm not sure what the next mod will be. Any suggestions?

#2 Astrojensen

Astrojensen

    Fly Me to the Moon

  • *****
  • Posts: 5237
  • Joined: 05 Oct 2008
  • Loc: Bornholm, Denmark

Posted 26 November 2012 - 06:11 PM

Looks su-weet!


Clear skies!
Thomas, Denmark

#3 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 26 November 2012 - 06:17 PM

digital inclinometer, $30

I'm not sure what the next mod will be. Any suggestions?


If you already have a digital inclinometer perhaps an azimuth setting circle mod might also come in handy??

#4 Ed D

Ed D

    Gemini

  • *****
  • Posts: 3024
  • Joined: 30 Apr 2010
  • Loc: Sunny South Florida

Posted 26 November 2012 - 08:13 PM

Nice Dob!!! :bow:

How about a slewing handle like the one I have on Mighty Mouse? Makes it much easier to rotate scope when viewing near zenith. The location of the pivot bolt allows the handle to rotate into the base (OTA removed), getting it out of the way for transport to dark skies.

Ed D

Attached Files



#5 BDS316

BDS316

    Vanguard

  • -----
  • Posts: 2071
  • Joined: 16 Sep 2009
  • Loc: Sol 3

Posted 26 November 2012 - 08:21 PM

Good ideas so far....I haven't done the az circle yet because I couldn't figure out how to print one. If someone is going to NEAF and could bring one I could cover the cost of material and printing...

Where did you get the slew handle parts? I haven't had any major problems with the navigation knob.

One mod for which I have been searching for a long time is a decal/bumper sticker of the James Bond movie, "GoldenEye" for the side of the scope, ala Mickey Mouse in the above example.

#6 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 26 November 2012 - 08:55 PM

if you tell me the dimension I could format this az setting circle so you could take it to kinko's and have them print it on their large scale printers and laminate it.

from this site. setting circle

it would take 2 mins.

#7 astrogeezer41

astrogeezer41

    Vostok 1

  • *****
  • Posts: 102
  • Joined: 27 Aug 2010

Posted 26 November 2012 - 09:20 PM

That looks and sounds great Bryan! Thanks for sharing.
-Robert

#8 Jaimo!

Jaimo!

    Apollo

  • *****
  • Posts: 1339
  • Joined: 11 Oct 2007
  • Loc: Exit 135 / 40° North

Posted 26 November 2012 - 11:27 PM

I haven't done the az circle yet because I couldn't figure out how to print one.



Get the appropriate sized setting circle as a .pdf, copy it onto a flash drive, and take it to Kinko's to be printed on one of their large format printers. For regular paper it should not cost more than a few dollars.

Jaimo!

#9 BDS316

BDS316

    Vanguard

  • -----
  • Posts: 2071
  • Joined: 16 Sep 2009
  • Loc: Sol 3

Posted 27 November 2012 - 06:14 AM

if you tell me the dimension I could format this az setting circle so you could take it to kinko's and have them print it on their large scale printers and laminate it.

from this site. setting circle

it would take 2 mins.


The wood circle at the bottom of the rocker box is 19 inches in diameter, and the ring can be no more than 1" thick, as it would have to be on top of the bottom of the rocker box, ie it can't go in between the ground board and the rocker box.

Thanks for your help, computers are really not my thing, which is why I'm a Dob guy. Up til now, my club members have apps in their smartphones that provide me with the alt components of what I'm loking for, then I pan in azimuth til I find it.

#10 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 10:41 AM

lets see if this works...

click on the attachment and download the file.

here's an image of what it looks like.

Posted Image

don't download this image download the attachment. :grin:

Attached Files



#11 BDS316

BDS316

    Vanguard

  • -----
  • Posts: 2071
  • Joined: 16 Sep 2009
  • Loc: Sol 3

Posted 27 November 2012 - 10:44 AM

lets see if this works...


Thanks. I printed it and now I take it to Kinko's so they can enlarge it and laminate it?

#12 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 10:48 AM

they print it on 24x36 glossy paper. they laminate it.

its already formatted for 24x36 paper. they don't have to enlarge it. they have to make sure they don't print to fit checked.

bring a ruler with you so you can measure it to make sure they print it correctly.

#13 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 27 November 2012 - 12:23 PM

The reason I haven't used any one of several degree circle files that are available is due to the small size of the fonts which are difficult for me to see with my old eyes without having to squat down each time to get close to the setting circle. I like to be able to just glance down from my eye piece position to see the azimuth reading.
For this reason I've been drawing my own legible degree circles directly onto the ground boards.

Here's a pic of the current ground board for my new base I'm building, hand drawn setting circle in 5 degree increments. When I find a suitable degree circle with big bold numbers I'll print it and paste it on this ground board.

Attached Files



#14 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 01:39 PM

Thanks. I printed it and now I take it to Kinko's so they can enlarge it and laminate it?



after reading gastrol's post about being able to see, what if it was white numbers and tic marks on a black background.

in the dark you want the numbers to lightup instead of the background?

like...

Attached Files



#15 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 27 November 2012 - 02:11 PM

after reading gastrol's post about being able to see, what if it was white numbers and tic marks on a black background.

in the dark you want the numbers to lightup instead of the background?

like...

I think that with large fonts would be great!

#16 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 02:36 PM

here's an 18.5 circle

Attached Files



#17 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 02:40 PM

here's a 19in black version with larger numbers

Attached Files



#18 RAKing

RAKing

    Fly Me to the Moon

  • *****
  • Posts: 6242
  • Joined: 28 Dec 2007
  • Loc: West of the D.C. Nebula

Posted 27 November 2012 - 03:05 PM

Here's one - order up a 3-vane spider and get a nice quartz secondary while you're at it. :)

This spider shows six dimmer difraction spikes and allows me to see double stars much better. The new secondary holder and mirror also work better. The secondary is easier to collimate if necessary and holds collimation much better. You can get rid of those Bob's knobs.

Yes, it's a little expensive and so is the Zambuto mirror down at the other end of the tube. Now THAT should be your next upgrade. :lol:

Cheers,

Ron

Attached Files



#19 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 27 November 2012 - 03:08 PM

Thank you Pinbout! ...for the 18.5 circle! I'll have Kinko's print one up.

#20 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 27 November 2012 - 03:17 PM

The wood circle at the bottom of the rocker box is 19 inches in diameter, and the ring can be no more than 1" thick, as it would have to be on top of the bottom of the rocker box, ie it can't go in between the ground board and the rocker box.


For your application where you want to mount the degree circle on the upper rotating base board instead of the ground board, the setting circle has to read counter-clockwise.

#21 Gastrol

Gastrol

    Apollo

  • *****
  • Posts: 1297
  • Joined: 04 Nov 2011
  • Loc: los angeles

Posted 27 November 2012 - 08:57 PM

Thanks again for the setting circle file Pinbout. I was able to get a couple of prints made just down the street from where I work. The numerals are huge and very visible....I love it.

Attached Files



#22 Ed D

Ed D

    Gemini

  • *****
  • Posts: 3024
  • Joined: 30 Apr 2010
  • Loc: Sunny South Florida

Posted 27 November 2012 - 09:50 PM

"Where did you get the slew handle parts?"

All salvaged stuff. The tube is from a carbon fiber bow stabilizer that was broken and no longer used. I made the knob on the end from black delrin on my mini-lathe. The aluminum was scrap that I also turned, as well as milling a flat where it attaches to the base with my milling attachment.

"One mod for which I have been searching for a long time is a decal/bumper sticker of the James Bond movie, "GoldenEye" for the side of the scope, ala Mickey Mouse in the above example."

I found my vinyl decals on eBay, pretty cheap, too. I can tell you're younger than me. That's not Mickey Mouse, it's Mighty Mouse. MM was a cartoon super hero similar to Superman. The little guy packed a big punch out of proportion to his size.

Ed D

#23 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 10:43 PM

Quote:
--------------------------------------------------------------------------------

The wood circle at the bottom of the rocker box is 19 inches in diameter, and the ring can be no more than 1" thick, as it would have to be on top of the bottom of the rocker box, ie it can't go in between the ground board and the rocker box.



--------------------------------------------------------------------------------



For your application where you want to mount the degree circle on the upper rotating base board instead of the ground board, the setting circle has to read counter-clockwise.



here's one in reverse if that works for you.

Attached Files



#24 Pinbout

Pinbout

    Cosmos

  • *****
  • Posts: 7793
  • Joined: 22 Feb 2010
  • Loc: nj

Posted 27 November 2012 - 11:31 PM

I went to bestbrandsoftheworld website and they have a goldeneye logo that you can download.

it's a vector format so you could send it to someone that would print and silhouette cut the logo with outdoor inks and the back with adhesive.

Attached Files



#25 BDS316

BDS316

    Vanguard

  • -----
  • Posts: 2071
  • Joined: 16 Sep 2009
  • Loc: Sol 3

Posted 28 November 2012 - 06:24 AM

I went to bestbrandsoftheworld website and they have a goldeneye logo that you can download.

it's a vector format so you could send it to someone that would print and silhouette cut the logo with outdoor inks and the back with adhesive.


Thanks!!! Who does that kind of stuff?






Cloudy Nights LLC
Cloudy Nights Sponsor: Astronomics